Computers are useless without a monitor. You can't surf the Net or see what you typed on the keyboard. It's a good thing that computer monitors are virtually trouble free. Besides checking to see if it's plugged in and making a few adjustments there's little you can do to fix it without specialized help. Even so, let's take a look at how they work and how to tackle something you can fix, the monitor fuse.
How Does It Work?
Components of a typical computer monitor. |
A computer monitor, sister to the television monitor, displays information from a computer on a screen. The monitor uses digital values sent by a computer processor to create a stream of electrons that light up phosphors on the inside of the screen. The signals are in each of the three primary colors, combined into various color signals that seem to move across the screen. Portable computers use a screen made up of liquid crystal display (LCD) cells instead of phosphors. Computer monitors receive their signal from a monitor cable from the computer and their power from a separate electrical cord.
What Can Go Wrong?
Computer monitor problems are not always problems with the monitor. Testing of the monitor must be done with the computer . The monitor may not come on. The image on the screen may not be clear and bright
How Can I Identify the Problem?
If the monitor does not come on, make sure there is power to the electrical receptacle . Check the electrical cord . Check the connections between the monitor and the computer and make sure the computer is on. Test the line fuse (see below).
Interior of a computer monitor. Identify but don't touch the power supply. |
If the image on the screen is not clear and bright, check your owner's manual for instructions on adjusting the monitor. Typically there are adjustment buttons on the monitor face below the screen.
What Parts, Materials, and Tools Do I Need?
Replacement cables and fuses are available from the manufacturer as well as from local computer shops. Tools you may need to access, test, and fix a computer monitor include these:
- Screwdrivers
- Multimeter
What Are the Steps to Fixing It?
Fix-It Tip
A computer monitor gets its instructions from a video controller card in the computer. The card may be an add-on expansion card or it may be built into the main circuit board, called the motherboard. If it is a separate card, you may need to open the computer and make sure the card is firmly connected. Also check the flat data cable that runs between the video card and the motherboard, if so equipped.
Locate, remove, and test the line fuse, typically located near the power cord entry. |
Test and replace a monitor fuse:
1. Disconnect the monitor from the electrical receptacle and from the computer processor.
2. Lay the monitor on a padded surface and remove the housing screws (some may be under pop-out tabs).
3. Slide the rear housing off.
4. Locate the line fuse typically near the power cord entrance. Remove the fuse from its holder and test it with a multimeter. Replace the fuse if it is faulty.
Caution!
For safety, follow the manufacturer's instructions in the owner's manual to discharge the video tube before working near it. In most cases this means using jumper wires to connect a 10,000-ohm resistor between the chassis ground or common ground and a screwdriver, and shorting the high-voltage lead by inserting the screwdriver under the suction cup.
Troubleshooting Tips for New Monitors
You are encouraged to make links to this article from your website and tell your friends
Here are some basic trouble shooting tips for new monitors:
- The picture does not appear
- Check to make sure the signal cable is firmly connected in the socket.
- Check to see if the computer system's power is ON.
- Check that the Brightness Control is at the appropriate position, not at the minimum.
- The Screen is not synchronized
- Check to make sure the signal cable is firmly connected in the socket.
- Check that the output level matches the input level of your computer.
- Make sure the signal timing of the computer system is within the specification of the monitor.
- The position of the screen is not in the center
- Adjust the H-Size, H-Phase or V-Size, V-Center controls.
- Check if the signal timing of the computer system is within the specification of the monitor.
- The screen is too bright or too dark
- Check if the Brightness or contrast control is at the appropriate position, not at the maximum or minimum.
- Check if the specified voltage is applied
- Check if the signal timing of the computer system is within the specification of the monitor.
- Especially, check the horizontal frequency.
- The screen is shaking
- Move all objects that emit a magnetic field, such as a motor or transformer, away from the monitor.
- Check if the specified voltage is applied.
- Check if the signal timing of the computer system is within the specification of the monitor.
Related Articles
How to Change Mother Boards in Desktop?
How to Upgrade a Computer's BIOS
No comments:
Post a Comment